2025-03-28 | | Total: 8
We report on experimental evidence of muon generation from a laser-wakefield accelerator driven by a PW-class laser. The muons were generated following the interaction of a GeV-scale high-charge electron beam with a 2 cm-thick Pb target and were detected using a Timepix3 detector placed behind a suitable shielding configuration. Data analysis indicates a $95\pm3$ % confidence of muon detection over noise, in excellent agreement with numerical modelling. Extrapolation of the experimental setup to higher electron energies and charges suggests the potential to generate approximately $10^4$ muons/shot with multi-PW lasers and to direct them onto cm$^2$-scale areas for applications. The results presented here demonstrate the possibility of muon generation using high-power lasers and establish a foundation for the systematic application of laser-driven muon beams.
A key open question in astrophysics is how plasma is transported within strongly magnetized, rapidly rotating systems. Magnetic reconnection and flux tube interchange are possible mechanisms, with Jupiter serving as the best local analog for distant systems. However, magnetic reconnection at Jupiter remains poorly understood. A key indicator of active magnetic reconnection is the ion diffusion region, but its detection at Jupiter has remained unconfirmed. Here, we report a unique magnetic reconnection event in Jupiter's inner magnetosphere that presents the first detection of an ion diffusion region. We provide evidence that this event involves localized flux tube interchange motion driven by centrifugal forces, which occurs inside a thin current sheet formed by the collision and twisting of two distinct flux tubes. This study provides new insights into Io-genic plasma transport at Jupiter and the unique role of magnetic reconnection in rapidly rotating systems, two key unresolved questions.
We discuss the main elements of a collider facility based on proton-driven plasma wakefield acceleration. We show that very competitive luminosities could be reached for high energy $e^+e^-$ colliders. A first set of parameters was developed for a Higgs Factory indicating that such a scheme is indeed potentially feasible. There are clearly many challenges to the development of this scheme, including novel RF acceleration modules and high precision and strong magnets for the proton driver. Challenges in the plasma acceleration stage include the ability to accelerate positrons while maintaining necessary emittance and the energy transfer efficiency from the driver to the witness. Since many exciting applications would become available from our approach, its development should be pursued.
We present the AGATE simulation code, a Python-based framework developed primarily for solving the magnetohydrodynamics (MHD) equations while maintaining adaptability to other equation sets. The code employs a modular, object-oriented architecture that separates interface specifications from numerical implementations, allowing users to customize numerical methods and physics models. Built on a Godunov-type finite-volume scheme, AGATE currently supports the ideal, Hall, and Chew-Goldberger-Low (CGL) MHD equations, with multiple acceleration options ranging from Numpy to GPU-enabled computation via NVIDIA CUDA. Performance testing demonstrates that our GPU implementations achieve 40-60x speedups over CPU versions. Comprehensive validation through established benchmarks confirms accurate reproduction of both linear and nonlinear phenomena across different MHD regimes. This combination of modularity, performance, and extensibility makes AGATE suitable for multiple applications: from rapid prototyping to production simulations, and from numerical algorithm development to physics education.
The 2-D edge plasma fluid transport code, UEDGE has been used to simulate the edge region of circular limiter plasmas of ADITYA-U for modelling the measured electron density profile. The limiter geometry of ADITYA-U has been introduced in the UEDGE code, which is primarily developed and used for divertor configuration. The computational mesh defining the limiter geometry is generated by a routine developed in-house, and has successfully been integrated with the UEDGE code to simulate the edge plasma parameters of ADITYA-U. The radial profiles of edge and scrape-off layer (SOL) electron density, ne and temperature are obtained from the simulations and used to model the measured ne profile using Langmuir probe array. It has been found that a convective velocity, vconv. is definitely needed in addition to the constant perpendicular diffusion coefficient, D throughout the edge and SOL regions to model the edge ne profile. The obtained vconv. is inward and radially constant with a value of 1.5 m/s and the radially constant D is ~ 0.2 m 2/s. The value of D ~ 0.2 m2/s is found to be much less than fluctuation induced diffusivities and lies in-between the neoclassical diffusivity and Bohm diffusivity estimated in the edge-SOL region of ADITYA-U tokamak. Furthermore, the transport of radial electron heat flux is found to be maximizing near the limiter tip location in the poloidal plane.
We investigate the behavior of heavy impurities in edge plasma turbulence by analyzing their trajectories using the Hasegawa-Wakatani model. Through direct numerical simulations, we track ensembles of charged impurity particles over hundreds of eddy turnover times within statistically steady turbulent flows. Assuming that heavy impurities lag behind the flow, a novel derivation of relaxation time of heavy impurities is proposed. Our results reveal that heavy impurities can cluster within turbulence. We provide multiscale geometrical Lagrangian statistics of heavy impurities trajectories. To quantify directional changes, we analyze the scale-dependent curvature angle, along with the influence of the Stokes number on the mean curvature angles and the probability distribution function of curvature angles.
A source of high-energy photons, ions, and positrons can be attained with the interaction of ultra-intense femtosecond laser pulses with advanced nanostructured targets. We present and characterise a numerical model that mimics the foam deposition process on solid substrates, as it occurs in Double-Layer Target (DLT) manufacturing. The model is integrated into Particle-In-Cell (PIC) simulations in full 3D geometry to study electron acceleration, consequent high-energy photon emission, proton acceleration, and pair production with realistic target and laser parameters. We highlight the importance of realistic foam morphology modelling even at high-laser intensity and the need for specific optimisation of target parameters with realistic PIC simulations to improve radiation production efficiency. Our study shows that the DLT could be a compact multi-purpose scheme to achieve high-brightness photons and high-energy protons and to observe and optimise non-linear Breit-Wheeler pair production.
Ultra-intense laser-matter interactions are often difficult to predict from first principles because of the complexity of plasma processes and the many degrees of freedom relating to the laser and target parameters. An important approach to controlling and optimizing ultra-intense laser interactions involves gathering large data sets and using this data to train statistical and machine learning models. In this paper we describe experimental efforts to accelerate electrons and protons to $\sim$MeV energies with this goal in mind. These experiments involve a 1 kHz repetition rate ultra-intense laser system with $\sim$10mJ per shot, a peak intensity near $5 \times 10^{18}$ W/cm$^{2}$, and a "liquid leaf" target. Improvements to the data acquisition capabilities of this laser system greatly aided this investigation. Generally, we find that the trained models were very effective for controlling the numbers of MeV electrons ejected. The models were less successful at shifting the energy range of ejected electrons. Simultaneous control of the numbers of $\sim$MeV electrons and the energy range will be the subject of future experimentation using this platform.